A hammock, especially an ultralight like the sub-2-pound Hennessy Backpacker A-sym, makes life very sweet for backpackers. But in the desert, or on a beach, while you still get the "tent" benefits, you no longer enjoy the comfort of hanging suspended in the air, above the cold, hard ground. In addition, you have snakes, spiders, and scorpions to contend with, and you get the worst of the dust. For another twenty or thirty dollars, and a few more pounds weight, you can hang your hammock just about anywhere using this approach, and you don't need to worry about critters, nor bring your sleeping bag and pad.
EditSteps
- 1Have a hardware store cut you two pieces of 1/16 inch (1.5mm) aircraft cable, each at least twenty feet long. Buy at least six (6) 1/16 inch (1.5mm) cable clamps while you're there, along with four (4) 1/2 inch (1.27cm) by 10 inch (25cm) lag bolts and two shorter lag bolts not less than 6 inches (15cm) long. Two pieces of one inch (2.5cm) round or square aluminum tubing, at least 4 feet (1.2 meters) long, are necessary also. If you don't have an assortment of hardware at home, buy two 1/4-20 x 2" (6.35mm x 5cm) bolts and nylock nuts, or two 1/4 x 2" (6.35mm x 5cm) hitch (or clevis) pins with hitch pin clips.
- 2Using the cable clamps, make a loop on each end of each cable. Three clamps for each loop are recommended for safety, but for reasons explained below, this overkill should not be necessary.
One end of a cable looped over a lag bolt in the ground - 3Drill a 1/4 inch (6.35mm) hole through one end of each tube, about 2 inches (5cm) from the end. Through each of these holes, insert a bolt with locknut, or a clevis pin with a hitch pin clip.
Clevis pin supporting finished assembly - 4Using a ratcheting socket wrench, screw 6-inch (15cm) or longer lag bolts into the ground about 8 to 12 feet apart (points C and D in the drawing). Leave only about 1/2 inch (1.27cm) sticking out of the ground. The poles go over the heads of the bolts, and they keep the base of the poles from shifting position.
Layout as seen from above - 5At point A in the drawing, screw in one of the 10-inch lag bolts. The distance, assuming 20-foot (6 meter) cables and 4-foot (1.2 meter) poles, would be about 9 feet (2.7 meters) from point C.
- 6Removing the nuts from one of the cable clamps, make a loop at about the midpoint of the first aircraft cable, just big enough to fit over the pole. Holding the pole upright, slide the loop so that the cable between points A and C is very tight. Screw the nuts back on tight.
Zoom in to see both sides of loop packed into the V-notch - 7Screw in a 10-inch (25cm) lag bolt at point B, securing the first pole. Have a friend hold it upright if possible while locating point B, otherwise use stones or some other means to make sure the pole is (close to) perfectly upright when the anchoring cable is tight.
- 8Repeat the previous three steps for points D, E, and F, using the second piece of aircraft cable.
- 9Mount your hammock, using two half hitches at point C, and a taut-line hitch at point D. Slide the hitch until the hammock rope is very tight.
Two half hitches at point C - 10Sit in the middle of the hammock, and make sure your bottom doesn't hit the ground. If it does, adjust the taut-line hitch at point D. Practically speaking, there will be some stretch in the rope and fabric which will necessitate performing this step 3 or more times until everything is tight. If there is no more "take-up" room on the side with the taut-line hitch, loosen it; undo the two half-hitches at point C; and re-tie them closer to the hammock. Then you will have more room for adjustments. Ideally you will be only an inch or two above the ground when the setup is complete, meaning only a slight impact if something breaks or a lag bolt pops out of the ground.
Close-up of taut-line hitch - 11With the working end of the taut-line hitch, tie another two (or more) half hitches around the cable, in case the wind lifts the hammock off the poles while you're not in it. Otherwise you'll be chasing it across the desert, then finally extracting it from a cactus or mesquite bush.
With the working end of the taut-line hitch, tie another two (or more) half hitches around the cable, in case the wind lifts the hammock off the poles while you're not in it. - 12Enjoy sleeping in your hammock as long as you stay in this location.
- Note: There is no need to remove the cable clamps when you break camp. The bolts or clevis pins may also be left in the poles; so the only thing necessary to do is remove the lag bolts and pack everything up.
- Note: There is no need to remove the cable clamps when you break camp. The bolts or clevis pins may also be left in the poles; so the only thing necessary to do is remove the lag bolts and pack everything up.
EditTips
- The lag bolts may not work in loose sand. Research different types of tent pegs to find some that work in your target area.
- Two more 6 inch (15cm) lag bolts will enable attaching side adjustment cords, and rain fly, if necessary.
- Ignoring Hennessy's recommendation to install the hammock at "chair height" allows you to use the shortest possible lag bolts and only one clamp per loop, since the impact will be minimal if the setup collapses from only an inch (2.5cm) above the ground.
EditWarnings
- Some hard-core ultralight backpackers will want to try using their telescoping hiking poles, which they're carrying anyway, to eliminate the long aluminum poles. They will most likely break, as seen here after one such attempt. A better alternative would be to make the aluminum poles double as your hiking poles, or as part of your backpack frame.
EditThings You'll Need
- During initial setup at home
- Drill with 1/4" (6.35mm) titanium or cobalt drill bit
- Small adjustable wrench, or socket to fit aircraft cable clamp nuts
- During setup and at campsite
- Two (2) 1" x 48" (2.5cm x 18.8cm) pieces of round aluminum tubing
- Four (4) 1/2" x 10" (1.27cm x 25cm) lag bolts
- Two (2) 1/2" x 6" (1.27cm x 15cm) lag bolts
- Socket wrench to fit lag bolts
- Two (2) 1/16" x 20' pieces of aircraft cable
- Six (6) 1/16" (1.5mm) aircraft cable clamps
- Two (2) 1/4" x 2" (6.35mm x 5cm) bolts with locknuts, or clevis pins with hitch pin clips
- Hammock
0 comments:
Post a Comment